View and Download Digital Watchdog VMAX A1 DW-VAONE 41TB user manual online. VMAX A1 DW-VAONE 41TB dvr pdf manual download. Also for: Vmax a1 dw-vaone 43tb, Vmax a1 dw-vaone 81tb, Vmax a1 dw-vaone 82tb, Vmax a1 dw-vaone 83tb, Vmax a1 dw-vaone 42tb, Vmax a1 dw-vaone 84tb, Vmax a1. View and Download Digital Watchdog VMAX A1 DW-VAONE 41TB user manual online. VMAX A1 DW-VAONE 41TB dvr pdf manual download. Also for: Vmax a1 dw-vaone 43tb, Vmax a1 dw-vaone 81tb, Vmax a1 dw-vaone 82tb, Vmax a1 dw-vaone 83tb, Vmax a1 dw-vaone 42tb, Vmax a1 dw-vaone 84tb, Vmax a1.
First off, I am assuming that your AirPort Extreme Base Station is the ONLY router in your current network configuration. That is, is it connected directly to an Internet modem by Ethernet and that modem is in bridge mode (not providing NAT & DHCP services).
Dw Vmax For Mac
To successfully access an IP camera on the local network from the Internet, the following basics need to be taken care of:
- Install the camera(s) and verify that you can access them from the local network.
- Configure port mapping/forwarding on your router. Typically, IP cameras require at least two ports: 1) A web port for administering the camera; Usually TCP port 80, and 2) A streaming port to broadcast the camera video feed; Usually UDP port 9000. Note: You should check with your camera's documentation for the exact ports required.
- If the camera is attached to a computer, you will need to configure the computer's firewall to open the same ports as in step 2 above.
- Test your network. Use CheckIP to determine your router's current WAN-side (public) IP address. Then, from a remote location (not from a computer on the local network), use the DynDNS Open Port Tool to verify that the required ports are open. Success is an 'Open' response from the Tool.
The following are general instructions on how to configure the AirPort for port mapping:
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
Dw Vmax For Mac
1. Reserve a DHCP-provided IP address for the IP Camera.
AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
- On the DHCP tab, click the '+' (Add) button to enter DHCP Reservations.
- Description:
- Reserve address by: MAC Address
- Click Continue.
- MAC Address:
- IPv4 Address:
- Click Done.
2. Setup Port Mapping on the AEBSn.
AirPort Utility > Select the AEBSn > Manual Setup >Advanced > Port Mapping tab
- Click the '+' (Add) button
- Service:
- Public UDP Port(s): 9010, 9011
- Public TCP Port(s): 80
- Private IP Address:
- Private UDP Port(s): 9010, 9011
- Private TCP Port(s): 80
- Click 'Continue'
Feb 3, 2013 2:19 PM
First off, I am assuming that your AirPort Extreme Base Station is the ONLY router in your current network configuration. That is, is it connected directly to an Internet modem by Ethernet and that modem is in bridge mode (not providing NAT & DHCP services).
To successfully access an IP camera on the local network from the Internet, the following basics need to be taken care of:
- Install the camera(s) and verify that you can access them from the local network.
- Configure port mapping/forwarding on your router. Typically, IP cameras require at least two ports: 1) A web port for administering the camera; Usually TCP port 80, and 2) A streaming port to broadcast the camera video feed; Usually UDP port 9000. Note: You should check with your camera's documentation for the exact ports required.
- If the camera is attached to a computer, you will need to configure the computer's firewall to open the same ports as in step 2 above.
- Test your network. Use CheckIP to determine your router's current WAN-side (public) IP address. Then, from a remote location (not from a computer on the local network), use the DynDNS Open Port Tool to verify that the required ports are open. Success is an 'Open' response from the Tool.
The following are general instructions on how to configure the AirPort for port mapping:
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the IP Camera.
Dw Vmax Download For Mac
To successfully access an IP camera on the local network from the Internet, the following basics need to be taken care of:
- Install the camera(s) and verify that you can access them from the local network.
- Configure port mapping/forwarding on your router. Typically, IP cameras require at least two ports: 1) A web port for administering the camera; Usually TCP port 80, and 2) A streaming port to broadcast the camera video feed; Usually UDP port 9000. Note: You should check with your camera's documentation for the exact ports required.
- If the camera is attached to a computer, you will need to configure the computer's firewall to open the same ports as in step 2 above.
- Test your network. Use CheckIP to determine your router's current WAN-side (public) IP address. Then, from a remote location (not from a computer on the local network), use the DynDNS Open Port Tool to verify that the required ports are open. Success is an 'Open' response from the Tool.
The following are general instructions on how to configure the AirPort for port mapping:
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the IP Camera.
Dw Vmax Download For Mac
AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
- On the DHCP tab, click the '+' (Add) button to enter DHCP Reservations.
- Description:
- Reserve address by: MAC Address
- Click Continue.
- MAC Address:
- IPv4 Address:
- Click Done.
2. Setup Port Mapping on the AEBSn.
AirPort Utility > Select the AEBSn > Manual Setup >Advanced > Port Mapping tab
- Click the '+' (Add) button
- Service:
- Public UDP Port(s): 9010, 9011
- Public TCP Port(s): 80
- Private IP Address:
- Private UDP Port(s): 9010, 9011
- Private TCP Port(s): 80
- Click 'Continue'
Feb 3, 2013 2:19 PM
